Noordkaper 46

The true life on board of a well sailing cruising yacht.
Easy sailhandling, good sailer, in the deckhouse view all around upper deck, little draft, because of the large tankage a good radius of action, very fine classic lines.

Design: The sailing yacht made of steel is a design by M.Bekebrede. He has laid all his experience in designing sturdy, seaworthy sailing yachts in the Noordkaper. The yacht is especially suitable for sailors who are staying a long time on board, as making a long trip or ven living on it. In combination with a lift keel construction the Noordkaper is also suitable for shallow waters. Because of the double storey under the deck house the Noordkaper has a lot of space. It is possible to look around freely from the deckhouse in order to have a close contact with the world outside.

Sizes: The Noordkaper can be built in lengths between 35 and 60 feet.

Hull: The round bilge hull is built of digitally cut steel. Hull thickness 6 mm, deck and deckhouse 4 mm. Cabin edges are being semi round completed. Water-overflow-pits and bollards are made out of stainless steel. Aluminum hull also available

Deck house: From the U-bank in the deckhouse you have a clear view all around. There is a large chartable. A steering gear inside is optionally. The Noordkaper can be delivered with a classic upright deckhouse or an extended cutter deckhouse.

Paintwork: After completing the hull, the yacht will be thoroughly preserved with a two components epoxy paint system inside out. The colours will be selected by the customer. The quality of the present paint systems will reduce the amount of maintenance to a minimum.

Motor: The Noordkaper has a Yanmar diesel engine. Other brands are optional. The propeller shaft is water lubricated and has a thrust bearing. In the fuel system is a watershed double filter installed. The yacht is provided with a three-bladed fixed propeller.

Rigging: The Noordkaper is short rigged and normally equipped with a Furlex roller reefing jib, therefore is it possible to sail the yacht with a small crew. The mast and the gib are made of anoded aluminum. The deckfittings are mostly by Rutgerson with winches from Anderson.

Steering: Jefra transmission with a rod driving gear for a good feeling with a 107 cm wheel. Pedalstal model classic with steering compass engine control integrated.

Keel: The yacht is a longkeel yacht with a boxkeel from head till rudderheel. A liftkeel construction to serve the keel electric hydraulic from the cockpit is optional. In case of a liftkeel construction the draft will be reduced till a minimum of about 1.40 till 2.60 meter. The smart construction makes the keelbox almost invisible in the interior.

Tank: Three steel diesel tanks are welded in the hull. Depending on the size of the yacht, they have a capacity of 1200 litres in three tanks. It is possible to use the tank exclusively for the heater system or the generator. There are stainless steel drink water tanks built with a capacity of 600 litres and a stainless steel 180 litres foulwatertank with a capacity which depends on the chosen interior of the yacht.

Interior: From the floor the hull is well isolated with a 5-6 centimeters thick foam coating. The woodwork is made of mahogany. Teak or another kind of wood are optional. The space is divided according to the wishes of the customer. There is enough space for a separated shower and toilet, two sitting area’s and good sleeping places in separated cabins. In the yachts you find among other things hot and cold water, central heating, gel batteries, a coast connection with battery charger, vhf, a log and dept gauge. This all sums up to a complete yacht fitted with modern conveniences.

Sailing: The quality offshore cruising sails from De Vries Sails are delivered with a mainsail cover. Genua with UV protection on the Furlex roller reefing foresail. The boat is cutter rigged.

Electric:  24 Volt system 4x 140 Ah Mastervolt gel battery, 40A Mastervolt charger, shore power connection 25 mtr cable. Halogeen spots in interior.